08-Current Hayabusa / 07-13 GSXR1000 ECU Flashing Interface

$225.00

With a Boost by Smith interface you can now utilize your bike to it’s full capacity. This includes tuning the vacuum area maps, TPS maps, ignition maps, making your engine run very smoothly when cruising, and put down as much safe hp to the ground as possible. With our interface you can also view engine sensor data to ensure correct operation of vacuum, ambient air, temperature, tps, gear position etc. sensors with a laptop connected. Previously all of this was available only for technical folks with a strong do it yourself ambition but by making this re-flashing interface for you we have tried to bring this new technology to everyone.

Category:

Description

**Warning**  If your ECU has been flashed with other software besides ECU Editor, it is likely locked and won’t be able to be flashed with ECU Editor until it has been returned to stock using the software/hardware that originally flashed and locked it.  **Warning**

With a Boost by Smith interface you can now utilize your bike to it’s full capacity. This includes tuning the vacuum area maps, TPS maps, ignition maps, making your engine run very smoothly when cruising, and put down as much safe hp to the ground as possible. With our interface you can also view engine sensor data to ensure correct operation of vacuum, ambient air, temperature, tps, gear position etc. sensors with a laptop connected. Previously all of this was available only for technical folks with a strong do it yourself ambition but by making this re-flashing interface for you we have tried to bring this new technology to everyone.

I build the hardware interface that will allow you to use PetriK’s free software that he has provided all of us with to tune our bikes through the ECU. If you are a do-it-yourself-er there are schematics posted on the hack forum to build your own hardware interface. What I offer is a clean solution that has been tested prior to shipping, with written directions, videos, and tech support.

Some of the features include:

  • Ability to view all sensors data with a laptop connected
  • Ability to clear fault codes
  • Ability to change fueling maps (both IAP and TPS maps) for better, more precise tuning than piggyback systems.Ability to change ignition maps (you can add timing in the lower gears like a TRE does without messing up your gear based fuel curves)
  • Increase your factory rev limiter (current software supports up to 12,500 RPM)
  • Remove the 6th gear speed restriction with the click of a button
  • Ability to dis-able soft cut limiters which can burn up your NOS or Turbo bike, hard-cut shuts all injectors down vs just a couple.
  • Turn your ECU into an ignition / fuel kill box for use with an air/co2 shifter. Gen 2 Busas’s can utilize gear based engine kill times (different kill time for each gear)
  • Switch-able map selection for NOS, different turbo boost levels, fuel types etc
  • Import maps from other fuel tuning devices (testing phase right now)
  • Replace stock map sensor with GM 3 bar for boost referenced fueling for turbo bikes
  • Disable O2 sensor, pair valve, IAT sensor for dyno tuning purposes.
  • Ability to tune secondary throttle blade opening (don’t remove those secondary flies you will loose hp)
  • NOW AVAILABLE: ECU controlled progressive gear based Nitrous/Fuel/Ignition Ramp Rate Control. www.boostbysmith.com/ecunos2.html for details.
  • This works on Bking as well though at the moment doesn’t have as many features (B-king you can re-destrict, map fueling, increase rev limiter, use ecu as kill box, dis-able exup, canister, O2 sensor, pair valve)
  • As of 01/08/2010 07-11 GSXR1000 Functionality for fuel/ignition mapping, de-restriction, limiter increase added, more features to follow soon like shift kill etc.

The interface I am offering is about a 10 minute install.

  1. Insert 2 pins into previously empty locations on your ECU connector
  2. Insert 2 pins into previously empty locations on your yosh plug connector under the seat
  3. Plug the USB cable into your computer, plug the flashing box into the Yosh and SDS connectors under the seat and you are ready to go
  4. The box doesn’t stay on the bike, so you can tune all of these attributes and not have any additional boxes on the bike permanently installed.

    Requires not 1 single wire splice.

    That’s it! Now just install the software, open up a base map, and you are ready to start unlocking the full potential of your Suzuki Motorcycle

The software is available for download at:
http://ecueditor.com

ECU2

BoostBySmith ECU Flasher Harness Install 2013

DOWNLOAD ECU EDITOR

 

Please note that while I do my best to ship items the business day after they are ordered, I am not always able to do this.

If you have an urgent need for anything, please email me directly greg@boostbysmith.com.

Domestic:  I ship most packages USPS priority mail, which is advertised as 2-3 business days.
Smaller items with shipping rates at just a few bucks are sent USPS first class mail.
I can ship UPS ground as well.

International:  Due to long delays with USPS during Covid 19, I am only shipping via UPS.
The customer is responsible for any brokerage/customs fees.  My site is setup to add $55
for international shipments as this is the worst case for UPS with rare exception of a remote service
zone fee which I will contact you if this is the case.

In the event that shipping is less than $55 I will send a refund.  Feel free to contact me in advance and I can check exact shipping for you.

Additional information

Weight 1 lbs
Dimensions 12 × 12 × 12 in
Motorcycle

08-12 Hayabusa / 07-13 GSX-R 1000, 13-Current Hayabusa

Reviews

There are no reviews yet.

Be the first to review “08-Current Hayabusa / 07-13 GSXR1000 ECU Flashing Interface”

Your email address will not be published. Required fields are marked *

Post comment

You may also like…